Plywood is a versatile material that can be used in many different ways. One way to cut it into strips is to use a miter saw. This guide will show you how to do it correctly.

How To Cut Plywood Into Strips

Source: Diynetwork

How To Cut Plywood Into Strips

When it comes to cutting plywood into strips, the process is not as difficult as one might think. All you need is a sharp saw and some patience. First, buy a plywood sheet that’s of the appropriate size.

Make sure that the sheet is thick enough so that your cuts won’t end up being too shallow. Then, trim the edges of the plywood with a jigsaw. Finally, use a miter saw to cut the strips at an angle. Sand the edges of each strip for a more finished look.

Buy A Sharp Saw

If you want to cut plywood into strips, you’ll need a sharp saw. You can buy one at most lumberyards or hardware stores. Make sure the saw is properly sharpened and in good condition before using it.

  • You need to buy a sharp saw in order to properly cut plywood into strips. A dull or incorrectly-sharpened saw will make the job much more difficult and could even result in injury.
  • When buying a saw, be sure to choose one that is both sharp and comfortable to use. There are a number of different types of saws on the market, so it is important to find one that you are comfortable using. Some features that you may want to look for include an ergonomic design, adjustable blade height and depth, and a safety guard.
  • It is also important to keep the blade clean and lubricated in order to avoid binding or other problems during the cutting process. Cleaning and lubricating your saw regularly will help keep it running smoothly and prevent any accidents from occurring.
  • To ensure accurate cuts, always use a straight edge when cutting plywood strips. This will minimize the chances of errors occurring and will result in straighter pieces of wood.
  • Finally, remember that plywood is a very tough material, so be careful not to damage it while cutting it into strips

Trim The Edges Of The Plywood With A Jigsaw

If you need to trim the edges of plywood, a jigsaw is the tool to use. First, cut a piece of wood that’s the same size as the plywood you want to trim. Then, line up the edge of the plywood with the edge of the wood you’ve already cut and hold it in place. Next, use a saw blade to make a clean cut across the edge of the plywood.

  • Trim the edges of the plywood with a jigsaw to create clean, smooth edges. This will help to prevent warping and curling in the future.
  • Make sure that you use a clamped guide when cutting the plywood. This will ensure that your cuts are straight and even.
  • Use an accurate depth gauge when cutting the plywood so that you can avoid making excess cuts.
  • Be patient while trimming the plywood; it may take some time to get it just right.
  • Clean up any leftover sawdust or wood chips after trimming the plywood with a jigsaw by using a vacuum cleaner or a hose.

Use A Miter Saw To Cut The Strips At An Angle

If you want to make a piece of wood look like it has been cut with a saw, you need to cut it into strips at an angle. This can be done using a miter saw, which is a special type of saw that can be used to cut pieces of wood at an angle.

  • To cut the plywood strips at an angle, use a miter saw. Set the blade to the correct angle and start cutting the wood.
  • Make sure that you hold the plywood firmly so that it doesn’t move while you are cutting. This will help to ensure accurate cuts.
  • Keep a straight line while you are cutting, so that your strips are evenly cut.
  • If you need to make adjustments to your angle, use the fence on your miter saw to make the necessary changes.
  • Once you have finished cutting all of the strips, stack them up and use a jigsaw or drill to create any desired angles or cuts

Sand The Edges Of The Plywood Strip

Ready to start cutting your plywood strips? Take a few simple steps to ensure a smooth and even finish. Start by marking the edge of the plywood strip with a pencil or ruler.

Use a belt sander or an electric wood saw to sand the edges of the plywood strip until they are perfectly smooth. If you plan on using the plywood strips in a project that requires stability, such as mounting shelves, be sure to sand both sides of each strip before joining them together.

Joining the plywood strips together is just as easy as following these simple instructions: Center one strip over the other, line up the edges, and press down firmly with a hammer or screwdriver. Once you have joined all of your strips together, be sure to Sand the entire assembly again to ensure a perfect finish.

Now that you’ve cut your plywood strips, it’s time to start assembling your project!

Tools You’Ll Need

To cut plywood into strips, you’ll need a saw, clamps and a straight edge. First, mark the piece of plywood that you want to cut into strips on the edge that is facing the wood grain. Make sure the clamps are tight so the plywood doesn’t move while you’re cutting. Next, use the saw to cut the plywood strip along your marked line. Be careful not to cross the grain of the wood!


A jigsaw is a common tool that you’ll need to cut plywood into strips.

Power Saw

A power saw is also a common tool that you’ll need to cut plywood into strips.

Circular Saw

A circular saw is another common tool that you’ll need to cut plywood into strips.


Hammering nails can be a necessary step in the process of cutting plywood into strips.

Nail Gun

If you’re using a nail gun, make sure that you have the right ammunition and safety gear to protect yourself while working.

How To Cut Plywood Into Strips

There are a few different ways to cut plywood into strips. One is to use a handsaw or circular saw. Another is to use a jigsaw. The most common way to cut plywood is with a miter saw.

First, you need to find the right size of blade for the job. You also need to make sure that the blade is sharp and properly maintained.

Next, position the plywood so that the edge of the blade is against the wood and hold it in place with one hand. With your other hand, pull the trigger on the miter saw and watch as the blade slices through the wood.

Selection of the Right Plywood

The first step in cutting plywood into strips is to choose the right material. You’ll need something that’s strong enough to hold up to the rigors of your project, but also flexible enough to conform to unusual shapes. The best choice for general-purpose plywood is medium-density fiberboard (MDF). It’s a good all-around option and can handle a lot of abuse without breaking.

Chiseling Out The Strips

Once you’ve chosen your wood, the next step is to chisel out the strips using a hand saw or a power saw. Make sure to keep your cuts consistent and accurate so that you get perfect, even strips every time.

Sanding and Finishing

Once you’ve cut all of your strips, it’s time to sand them down and finish them off with a coat of paint or an epoxy sealant. This will help protect the wood from weathering and make it resistant to scratches and dents.

To Recap

There are a few simple steps you can follow to cut plywood into strips. First, identify the edge of the plywood you wish to cut. Second, measure the length of the strip you want and divide this number by 2.

Finally, use a saw to cut the plywood strip.

Similar Posts

Leave a Reply

Your email address will not be published. Required fields are marked *